Plumbing Essentials: An Essential for Installing a Bathtub
Plumbing Essentials: An Essential for Installing a Bathtub
Blog Article
We have found this article on A Step-by-Step Guide to Installing a Bathtub down the page on the net and reckoned it made good sense to write about it with you on my blog.
Setting up a bathtub isn't exactly rocket science, but it does need strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bathtub with a new one is also a reasonably hard task. If the old tub is conveniently obtainable, the job can move immediately; if you have to open up a wall to eliminate the old tub and also place the new tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task and also fit attempting it. As opposed to employing a service provider to take control of a halfway-completed task, it is better to think about utilizing one before you start. Opportunities are you may need an expert plumber to make tube links.
This short article will aid you mount a brand-new bathtub in your restroom if you have currently gotten a brand-new bathtub and do not require to alter the arrangement of your previous water pipes.
Your devices and also material checklist ought to comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather bothersome as a result of the restricted access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipelines. When the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Protect the tap in place with the supplier given backnut. Once the faucet is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be attached to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the called for placement. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bathtub until the spirit level reviews degree.
To install faucets, fit the bottom of the outermost adaptable faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the other faucet.
Switch on the water supply as well as examine all joints and brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally examine the overflow outlet and also the regular electrical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the producer's user's manual. Tiling and securing around the bath tub must wait till the bathtub has actually been made use of at the very least when as this will certainly settle it right into its final setting.
Planning for the Installment
First of all, the supporting structure provided with the bath must be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, causing the water to pass through the wall surface in between the bath and the tiling, resulting in issues with moisture and possible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can split rather very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly readily available on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that editorial on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a good friend on a different domain. Please take the opportunity to promote this content if you liked it. I take joy in reading our article about How to Install a Bathtub.
24-hour service? Dial here. Report this page